More timing gear

In a recent post, we looked at stripping the gear in the inner timing cover. This time, we are going to complete the strip in that area in preparation to splitting the crankcases.

As you will remember, I'd removed the dynamo sprocket after a bit of a struggle and went on to make a gudgeon pin puller so that I could lock the crankshaft, prior to removing the rest of the timing gear.

I locked the crank with a bit of 5/8" bar through the little end eyes, protecting the crankcase mouth with some strips of 3/8" MDF, then I knocked back the tab washers on the oil pump & camshaft nuts.

Both these nuts appear to have a 25/32" hexagon, close to 20mm - I used a 20 mm six sided socket. Fortunately neither nut was particularly tight and they came off with no drama.

The camshaft pinion is provided with two 1/4" BSC tapped holes, so its easy to pull the pinion off:

With the cam pinion out of the way, I could wind off the oil pump drive and remove the oil pump. It's a mazak pump - we'll think about replacing that at some point, but it probably won't be in the first phase of this rebuild. I also took the opportunity to remove the oil pressure relief valve while the cases were still in the engine stand - it's all present and correct, but its full of gunge.

The oil pump drive is damaged - it's old damage, not by me fortunately. We'll have to get it clean to see if it is usable:

I was concerned about pulling the crankshaft pinion off - or rather, I was concerned about spending more time making another puller. In the event, it moved with the slightest encouragement from a pair of screwdrivers.

So that's it for the moment - I just have to clean the parts up, inspect and store them before moving on to the crankcase and crankshaft.

I'll just have a sort through all this sludge...

Cake Run

Overcast and chilly but dry, and recovering from a couple of days with the grandchildren, today came another opportunity to give the SQ4 another test run after the summer oil leaks and HT problems which were eventually traced to be the cause of a persistent and long term misfire. Although the cold weather might be masking a hot weather running problem, the bike is running better than it ever has.

Preparing for the trip, I noticed the oil level was lower than expected, though a few minutes idling had it a little closer to normal. I topped it up, and resolved to look at it again when I got back.

A 27 mile around North Norfolk had me grinning from ear to ear as usual, though I thought the handling was a little uncertain; the brakes appear to be bedding in, the chain needs adjusting and the lower chain guard is clanking as usual.

Back in the workshop (after collecting the pear & ginger cake from the excellent Picnic Fayre in Cley), I set about adjusting the chain and rear brake. Since I was adjusting the chain, I removed the wheel to take off the chainguard - more on that in another post. I moved the chain back half a turn and lubricated it; I adjusted the brake up 3/8 of a turn and put an 1/8 of a turn on the front as well. The primary chain looked OK, and the oil level was good. I checked and nipped up all the spokes on the rear wheel.

Turning my attention to the engine, I had a good look around underneath. There was quite a leak coming from somewhere judging by the clean oil 'trails', possibly:

• the engine breather, which had a drip on the outlet pipe
• the sump plate or plug
• the front offside main bearing
• the oil filter
• the oil feed to the engine or to the top end
• a combination of several things

Essentially, there were too many possibilities to narrow it down. I tightened the oil feeds, the sump plate and plug, the crankshaft bearing cover and the timing cover but essentially none of them needed attention.

The front main bearing cover has a peculiar copper/asbestos gasket which looks more like an exhaust ring gasket and I suspect is wrongly installed. It's not the gasket I would have chosen for that application.

More later.

Gudgeon Pin Extractor

Gudgeon or wrist pins retain the piston to the connecting rod with varying degrees of clearance, transition or interference fit according to the predicted running temperature of the engine, and are retained by a circlip at each end in addition to any fit. This means that removal of the circlips will sometimes allow the pin to slide out, but more often than not you'll need to warm the piston such that it will release its grip on the pin. Obviously, belting the end of a tight pin will do your connecting rods no favours at all, so anything other than light tapping is a no-no.

A much better approach is to use a gudgeon pin extractor. These usually consist of a threaded rod passing through the pin, some means of holding the pin, a tube large enough to allow the pin to come out and a large washer to spread the load.

I made this extractor to deal with the FH gudgeon pins, which were quite tight. It is made of a bit of 1" tube, with a closed end turned from aluminium; that's M6 threaded rod in the middle. The tube is long enough to accommodate a 3" gudgeon pin.

A turned steel plug fits neatly into the gudgeon pin aperture in the piston and is reduced to just fit inside the pin such that it doesn't slop about. It's threaded M6 internally and is retained with a nut for the moment.

Here it is, set up and ready to extract the first pin:

Here's the extractor set up on the piston. The end of the tube is shaped to fit the piston, spreading the load over the piston wall:

A blast of heat on the piston crown and some steady winding are all that is necessary to draw the pin out of the piston, without placing any side load on the connecting rod. When you have done winding, the pin is neatly enclosed in the extractor:

Job done.

FH - inner timing cover

In the last instalment, we removed the outer timing cover to gain access to the dynamo drive, the ATD and the oil pump. We removed the dynamo drive chain but then stopped with this old, lightweight Japanese puller distorting itself while attempting to remove the large dynamo pulley on the idler pinion.

Over a week later, with three trips away for work I can tell you that the old puller never managed it and I had to make a new one. The new one, backed by a piece of 1" x 3/16" angle, is considerably stiffer though it loses out by having a coarse thread - the centre thread on a puller should be a fine, hard thread. Anyhow, it worked well enough and the dynamo pulley is now off.

Here we are - I told you it was off. Nothing untoward here apart from damage around the ATD which suggests it has been whirling around and rubbing the timing case:

The next step was to remove the inner case, which is held in place with four screws. A quick dose of the traditional remedy - leather hammer and impact driver, though not necessarily in that order, had it free in a jiffy. A mysterious 'tink' followed and this little chap appeared in the drip tray:

I wonder what it is?

Now we can see the crankcase, which looks fine & dandy. The idler will have to go back in to release the crankshaft & cam shaft nuts.

Here's the crankcase side of the inner timing cover. You can see the damage the loose ATD has caused in the top right of the picture.

And close up:

The magneto shaft, whilst it will turn the points, is very wobbly. This is more than a bearing problem - I think the shaft is broken.

Here's the timing cover in the parts washer, almost clean.

It was about now that I discovered you are not supposed to put paraffin (kerosene) in these little parts washers...