Showing posts with label wiring. Show all posts
Showing posts with label wiring. Show all posts

Friday, 9 January 2026

FH - not charging...

 Having learned that the FH will drain it's oil tank through the gear pump into the sump, I try to run it once a week or so during the winter. It was on one of these occasions that I noticed it wasn't charging and my first thought was to look at the dynamo to see if it had broken another chain.

Fortunately not - so I left it alone for a dose of thinking about.

Coming back the next day, I worked through the other electrical systems to see if anything jogged my thoughts and found the rear light wasn't working either: given that the ammeter and the rear light connect through the lighting switch I had a look under the top yoke:

Two wires had pulled out of the five way connector. Harness too tight or connectors not assembled properly in the first place?

Wednesday, 12 February 2025

FH - dashboard again

 A job I had been putting off for a while involved pulling the instrument panel off again. It involves fiddling around behind the headlamp, a particularly inaccessible area, and removing the handlebar clamp. It had to be done though, the indicator relay bracket was threatening to fret through some wires and the ammeter was popping out - not to mention the fact that I couldn't get the screws in to fasten the thing to the nacelle.

One of the problems with removing the dashboard is that you have to lift the handlebar clamp completely off. This is because the dashboard has been repaired where it sits under the handlebar clamp, and the slots are not really the right shape. One in particular fouls the stud in the handlebar clamp:


I marked the offending area on a bit of masking tape:


A few minutes with a file sorted that out, and now the clamp fits much more smoothly. You still have to lift it to remove the dashboard though.

The main job was to move the indicator relay. In a previous incarnation, I had it fitted under the rearmost speedometer nut and it was preventing me getting my hand in to fit the speedometer cable and to reconnect the wires to the headlamp switch.


What I've done today is make a new bracket for the indicator relay so that it's mounted under the ammeter in a corner of the nacelle that's out of the way:


I can get my hand underneath the dashboard now to reconnect all the wires and the speedometer cable. I made the main battery feed cable quite long when I built the wiring harness and this helps to reconnect it to the ammeter when you are fitting the dashboard.

Monday, 9 December 2024

FH - head steadies

 A couple of hours in the workshop yesterday saw a few little jobs closed off. This was the worst:


Access is not easy, but the secret is a short open spanner.

The head steadies are now fitted with full size 5/16" nuts, which entailed lifting the rocker box (twice) to get them in.

Next up was the timing side footrest, which wasn't fully tightened up - doing that enabled the exhaust fitting to be completed on that side, with the exception of the finned clamp.

I fitted the speedo cable, to find that the locating pin in the gearbox was missing. The AOMCC gearbox man has them available.

I spent a while poking around under the instrument panel, where the ammeter has lifted out of the position and the cable routing is poor:



I've almost fixed these problems, but the ammeter is still out of position and the wire from the lighting switch to the dipswitch is too short; the feed from the ammeter to the indicator relay is badly routed and consequently too short, and the indicator relay terminals are almost impossible to reach.

The instrument panel is going to have to come off again.

Saturday, 16 November 2024

FH - baby steps

 Aside from fixing the horn, there were a few more little steps towards completing the Huntmaster today. The package from Draganfly arrived this morning and in it we have the throttle stop which goes straight into position on the twist grip:


There's a few more bits of wiring we can do as well. First off the BPF connector in the headlamp has poor quality wires and undersized bullets so we can replace those by desoldering the terminals, replacing the wire and adding some good quality English bullets for connection to the headlamp wiring. We can also add a splice and a couple of extra bits of wire to earth the BPF connector to the headlamp shell and onward to the main earth and the battery. 

Additionally the pilot lamp holder was in really poor shape. The wire had started to degrade so it was really necessary to replace it. I used a small pop rivet to replace the terminal, and used a new piece of wire crimped into the pop rivet and provided with a bullet connector at the other end. 

I just need to find a full set of LED lamps from Paul Goff to complete the work on the lights.


The last thing was to fit one of the pillion footrest rubbers. The other one is waiting on a repair to the screw retaining the footrest to the frame.


Wednesday, 13 November 2024

FH - wiring the dashboard

 This will be the first time that I've wired up an Ariel with the separate instrument panel fitted to the swinging arm frame bikes with the headlamp nacelle. Looking at the wiring diagram it makes sense to wire up the panel separately from the rest of the bike, to be fitted later.

As you've seen, and in line with the wiring diagram, I have fitted a 5-way bullet connector between the main harness and the front end. Some of the cables from the instrument panel will go into this multiple connector, and others will stay on the panel whilst further connections will go into the headlamp. 

I made a start on the panel by fitting the ammeter and the light switch. I had the speedometer fitted as well, but found that the speedo lamp fitting was loose in the speedo body and the bulb holder could not be removed so I've sent this off for this to be repaired and the speedo overhauled.

Here's the initial layout. I've put all the wires in and crimped the ring terminals; the next step is to try this on the bike and see where the cable is going to route and how I can tie these cables together in sleeving.


This is the result. You can see I've terminated all the wires now, and added some sleeving and routed some of the wires around the top of the speedometer. I can't do much more until the speedo is back from Russell.

I need to clip the switch in and add the rubber ring around the switch and the ammeter, but it does work and I have both a rear lamp and a stop lamp. For some reason the horn doesn't work? 


It's alive!


Next stop on the wiring list is to add the combined horn button and dip switch. This is the original one and I have just removed the old wiring and clean the switch up with degreaser. More of that later.



Sunday, 10 November 2024

FH - more wiring

 Wiring jobs are plodding on at the moment. This next picture shows the splice that I have made to provide a battery feed to the horn and stop switch. It's quite difficult to follow the original wiring diagram and make all of these connections at the battery terminal with modern VRLA batteries with their tiny spade terminals.

It's soldered and covered with heat shrink sleeving.


Here is a view of the rear brake light switch. Behind the oil tank, in front of the mudguard and behind the toolbox is a very difficult position to get to to put that bullet connector in. Ariel clearly assembled the switch and the wiring before the oil tank went on - which reminds me, there is no seat bolt above the oil tank, so the tank will have to come off again!


You can also see in this picture that the rocker feed oil line is not very well fitted to the stub on the oil tank. I pushed this on a lot further.

This next one shows the wiring for the regulator, complete with the seal, clamp and split bullets:


That's the battery area complete. For the record, this is wired negative earth which means I will have to flash the dynamo at some point.


For some reason the battery lids are moulded with four cable access slots. This is because they are a copy of the original moulding which had to accommodate large Bakelite knobs for the battery terminals. I've filled two of these holes with black hot-melt glue.


Next stop, wiring up the dynamo. You can see the dynamo D connection on the left, as it connects directly to one of the brushes. The field F connection on the other side connects to one of the white field cables going into the body of the dynamo.

I oiled that felt before I closed the dynamo up.


That's the dynamo wiring sealed up. 


The last job today is to finish the wiring to the rear lamp. These are the finished cables from the harness with Japanese bullet connectors for the stop switch and rear lamp and a crimped and soldered eyelet for the earth.


The earth wire is attached to one of the rear lamp fixing bolts. 





Friday, 8 November 2024

FH - wiring harness

 I'm not going to blog the complete build of the wiring harness, because I've done that a few times already for the Square and the W/NG. What I will do is show you a few details of the harness as it comes together.

This picture shows the arrangement around the back of the toolbox. From the main harness there are branches going to the horn, to the regulator, to the battery and to the stop switch.

I will probably add a series of bullet connectors to allow me to separate the main harness from the harness going to the rear mudguard.

This next picture shows the main earth cable to the rear which splits into three near the indicators. There is a soldered splice under that heat shrink.

This picture shows the harness going to the rear of the bike with that soldered splice and the wires to the indicators and the rear lamp all covered with PVC sleeving, with a heat shrink section around the joint.


The bike is running an original Lucas 564 which needed to be rewired. I've replaced the cabling and used some heat shrink to provide some wear resistance where the wires go through the rear of the lamp. The connections to the bulb are blobs of solder flattened on the linisher.


Here's the engine earth. This is taken back to the main frame earth which is the upper of the two oil tank bolts. I need to clean the Wellseal off!


For the record this is how I have terminated the magneto kill switch. There is a length of cable, covered in heat shrink, passing through a small length of fuel line which sits neatly inside the thimble nut on the end of the magneto. This end is now weatherproof.


The other end of the magneto cutout cable is soldered into a push button at the handlebar. The joint is hidden by a piece of PVC sleeving pushed over the button - I didn't have any suitable heat shrink to bridge these two sizes.



Friday, 20 October 2023

FH - nacelle & handlebars

 I'm working on several fronts here, aiming to find problems and clear space so that I can start on the bottom end of the engine. Once that's in, there's polishing and plating, cables and wiring.

The nacelle went on relatively easily, though the trim on the front doesn't fit too well. That will need sorting out:


I planned to fit the instrument panel, mainly to avoid losing the trip reset cable but I found a few problems:
  • the speedo bracket only fits one way, basically because it's too wide. I fitted it by elongating the holes but it would be nicer if I made a new one.
  • the ammeter is one of those - - 0 - + ones, with no numbers. I'm not sure that's correct.
  • the Lucas U39 headlamp switch is damaged where the clip fits - people prise these out and the Bakelite breaks.
On the up side, both the light switch and the speedometer have PVC cables - maybe the whole bike was wired using that stuff.


Next - working through the little bags of screws, I find the grub screw for the steering lock, so that's fitted:


I treated the bike to a nice set of stainless steel handlebars from Draganfly - made in Bungay. The SQ4 has these too and they are very nice.

There's a lot of work to bring the levers up to scratch though!

FH - thinking about wiring

 This is the wiring diagram we will use for the FH. It comes from Pitman - Waller doesn't show a diagram for Ariel's of this period for some reason.


We’ll need some additions to that harness of course:
  • An earth cable from the rear light to a central earth point, including a connector to allow us to remove the rear part of the mudguard 
  • An earth cable from the magneto to the cutout button, including a connector to allow the cutout button to be removed
  • An earth cable for the headlamp
  • Wires for the indicators
  • A fuse
We will also rethink the 5 way connector block - it makes no sense to take the headlamp cables through it other than the main feed from the lighting switch. It’s the interface between the main harness and the instrument panel, so we can run the battery cables through it, the earths and possibly the yellow charging cable. 

Lucas started to adopt a standard approach to vehicle wiring in the 1930s, on the Austin 7. We can see that Ariel (supplied of course by Lucas ) followed this to some extent:
  • Black: Anything connected to the chassis earth;
  • Brown: Main battery distribution circuits, containing no fuses and no switches;
  • Red: Side, tail and instrument lighting; number plate illumination;
  • Blue: Headlamps;
  • White: An unfused feed, live only with ignition switch on;
  • Green: A fused feed, live only when the ignition switch is on;
  • Yellow: Circuits involved in or related to battery charging: dynamo, voltage regulator.
Lower level identification could be done by the use of coloured sleeves, as witnessed by the original looms with my 1951 Mk1 Square Four. The standard wasn't formalised until the late 1960's released of BS AU7.

It wasn't until the 1950s that PVC began to appear in wiring looms; hitherto, cables were covered in braided cotton.

This is the original loom from my 1954 BSA Bantam, setting the scene for the FH harness. We’ll do that in PVC.


Tuesday, 28 April 2020

QR50 - Wiring

It's a bit early to be looking at wiring up the QR50, but since we are on lockdown and my workshop is a few streets away I have resorted to bringing stuff to the house to work on. It's good to bring the wiring indoors - it's a nice clean job that you can do at your desk in the study.

This is virtually all I have, apart from the toasted generator stator I showed you in another post. This is the CDI unit:


And here it is again with all that insulating tape removed. If you look closely, you will see that some of the wires have been cut very short:


This is the whole 'harness', minus the sleeving. There isn't much to wire up on a QR50, but it is not supposed to look like this:


Before we start though we need a circuit diagram. Through a lot of research, Honda parts lists, generic CDI system diagrams and looking at the charred remains of the original loom I have come up with this:


There's a lot going on in this diagram, besides the connectivity of the various parts. Let's look at the way the system functions:

  • The Black and White wire (BW) wire is the exciter - it provides AC voltage to the CDI module
  • The Blue and Yellow wire (UY) is the trigger - it uses the hall effect sensor in the rotor to tell the CDI unit when to fire the coil
  • The kill switch earths the exciter coil through a second BW wire, preventing the ignition from working.
  • The Green and Yellow wire (GY) is connected to a micro-switch in the rear brake lever. According to the user manual, the engine won't start if the brake is not applied, and there is a spring loaded lever to hold the brake applied while you start (this disengages as soon as you squeeze the brake). I assume (at this point) that the switch is intended to break a ground connection when you apply the brake, but that this has no effect when the engine is running...
  • The Black and Yellow wire (BY) is the wire to switch the ignition coil.
  • The Green wires (G) are grounds.
In addition to the functionality, I have used this diagram to indicate cut wires - each cut wire has a number (1 to 16), and each cut wire has a connector (male, female or double female). The harness layout is shown in a simple sketch with rough dimensions; I have shown a length against each cut wire and summarised these to determine the total length of each colour. This list, along with the list of connectors, tells me what to order. I have followed Honda's practice of using the same 1.0 mm² wire throughout.

I'm going to use original type Japanese 3.2 mm bullet connectors throughout. These work beautifully and are protected from the weather - but you must select them according to the wire diameter.



Here are most of the parts we need:


First, I am using some tube crimps and solder to extend all the wires from the CDI unit to match the only remaining original wire, the ignition trigger. This is often tricky, as 40 year old wires are often too dirty to solder; this one has been OK, probably thanks to all the insulating tape.


I've protected these joints with heat shrink sleeving. I bought a selection of 8" lengths in various colours from eBay, and very useful it is too.


This is the CDI unit, finished with sleeving and boots as the original was. That large boot with the section change was made from a short length of heat shrink sleeving, partially shrunk over a small bottle of glue:


The parts list calls for a harness from the CDI unit leading up to the headstock area - this connects in the two handlebar switches.


Here's the finished stator:


Now I have the bike partly assembled, I can lay the harness out on it to see where the parts are routed and to ensure that I have sufficient length in each of the harness parts.