FH - followers, pistons and barrels

 With the little QR50 out of the way and the FH back on the bench, we can get on with the build. The barrel has been painted for a while, the bottom end is in the bike, there's no primary or timing side and no pistons. Off we go:

First step is to fit a circlip to each piston; the gudgeon pins come out with some mild warming and are refitted just as easily. As you can see, I've put a large rag under the pistons as I don't want a circlip in the crankcase at this stage, and the pins go back in and the circlips go on without any drama.

Next, we can refit the reground cam followers. I've ground the radius back into these such that they now have no wear grooves. The retaining screws and pins (with the missing ball) have been refitted:

Next, we fit the ring compressors - these are just strips of tin held in place with ty-wraps. These were cut for the SQ4 and are not really long enough for these larger pistons. You'll see the wood - these are to prevent the pistons rocking about when the barrel goes on.

Before the wood strips go in, we squirt oil all over both small ends. 

The wood strips are wide enough to completely stabilise the pistons while we put the barrel on, but first we use Threebond 1215 to apply the base gasket to the barrel, to keep it out the way. This wasn't ideal as I was forever wiping gasket goo off my gloves -  it would have been better to have the gasket, goo down, on the crankcase and apply the goo to the upper side after the barrel was over the rings.

After a lot of fiddling, swearing and anguish the barrel went down. The compression rings were not too bad but the three piece oil control rings, with their thin 'rails' were a pain to get in as they popped out of the compressors before they were caught by the barrel.

They went in eventually, and we can retain the barrels with four nuts.

FH Barrel

 While waiting for the kickstart rubber, I've degreased the FH barrel in the cleaning tank and given it  good scrub and scrape. Removing the rings from the new + 0.060" IMD pistons and testing them for fit reveals a nice 0.004" clearance in both barrels, per the IMD recommendation.

Therefore, it's time for a coat of engine paint. This is the same stuff I used on the W/NG which seems to have survived OK:

FH - Plastiguage and the big ends

 Next step is to check the big end clearances. I've measured the journals, but I wanted to get some evidence of the clearance that I had ended up with after fitting new -0.030" shells. There isn't much detail on what the acceptable clearance is  before you must regrind, other than the data describing the sizes you regrind to and the recommendation that there should be minimal clearance after regrinding.

Waller indicates 0.003"- 0.004" for the big end shells used on 1948-1955 Square Fours (Fifth edition page 37); Phil Irving quotes 0.001-0.0015" clearance per inch of diameter (Tuning for Speed 3rd Edition), which equates to 0.00165 - 0.0025" for my 1.65" big end. Mr. Irving, otherwise known as 'Slide Rule' using those delightful pseudonyms beloved of motoring writers in the '40's, also notes that the clearance can be much larger as long as oil pressure is maintained.

So, let's introduce Plastiguage. This is a paste, extruded into rods a bit like Plasticene. You trap a bit in the bearing and squash it, so that the known Plastiguage rod diameter is squashed to take up the clearance of the bearing - you then use the card provided to determine the clearance from the width of the squashed Plastiguage. Plastiguage comes in different sizes to measure different clearance ranges.

So, you cut a length to suite the bearing like this, and then you make up the bearing. You make sure the bearing is clean first.

When you open the bearing again you can see the squashed Plastiguage and you can compare it to the card. This suggests something like 0.002 - 0.0025" clearance for the drive side. I'm happy with that.

This is the timing side, and it's about the same:

All good there then. Next job is to make sure the oil flows into the big ends. I'll inject it into the timing side oilway:

And it comes out the drive side big end!

During this process, I removed (with a little heat) one of the gudgeon pins from the new IMD 7.25:1 pistons I got from the AOMCC so I could check the fit in the connecting rod little end bearings. This proved to be perfect once I had cleared a small burr from one side of both bearings; not sure how that came to be there.

Happy days.