Showing posts with label relief valve. Show all posts
Showing posts with label relief valve. Show all posts

Saturday, 9 August 2025

SQ4 - after the service

 A few little teething troubles appeared after the recent service, most notable of which was the oil pressure. Normally the oil pressure sits at 75 psi when cold and rolling at main road speeds, dropping to 25 psi idling after 15 miles or so.

Today, it was going up to 75, but intermittently dropping to 40 or so - very odd. I bled the Morgo again:

When that appeared to be happy - there were no bubbles I turned my attention to the relief valve.


See that bit of debris half way along the spring? I cleaned that out, and after a suggestion from Richard in the AOMCC, I changed the ball and reseated it.

I then rode to Cromer and back, clocking up about 13 miles - until it warmed up, it sat solidly at 75 psi and was still showing 50 psi when I got home. Back to normal.

It’s a bit snatchy at low speed. Initially I thought this was carburetion (not that I have changed anything), then perhaps transmission snatch, but all is normal there.

I’m going to retard the timing a bit.

Monday, 6 May 2024

FH - assembling the inner timing case

 Lots of work faces now, but an interim look at the cylinder head reveals that the valves and guides are beyond use - there is a couple of millimetres of rock at the edge of the valve head, with the valve half out of the guide. 

So, while I wait for a new set of guides, valves and springs let's start on the timing gear. Fitting the pinions is straightforward once I have deburred the Woodruff keys. The timing is set to the marks:

I've cleaned the dynamo straps since you have to have the inner timing case off to fit them. I'll plate these at some stage if I'm not too busy riding the bike:


The oil pressure release valve has been through the ultrasonic bath and has a new 5/16" ball. The old one was grooved and rusty:


Next, for the record, the pump drive washer is fitted:


I've made a small spacer from gasket paper for the end of the pump. Each of the stud threads has been cleaned up and fitted with blue Loctite thread lock:


I've used the original deep nuts - I've flattened these and recut the threads, adding a chamfer:


If you read my last post, you'll know that there is supposed to be a thrust washer in the nose of the pump, under the circlip. It needs to be 14.5 mm OD x 2 mm thick.


I had a bit of 3/4" EN11 in the lathe to make a late-pattern QD hub nut spanner, so I've used a bit to make the thrust washer:


I've left the pip in it to make it easier to get out. Next, the pump drive lock washer - the inner tang fits in a groove (like a keyway only less deep) in the end of the crankshaft. The tang on the new one is much wider than the remains of the one on the old washer  - time to get the needle files out:


With that in place, we can knock the tab washer down. On the crankshaft, I have bent the washer over both the lock nut and the pump drive sleeve:


For the record, the cam drive tab washer is knocked down too:


I've also finished polishing the timing cases:


I had to clean a lot of carbon off the timed breather sleeve before it would fit, and relieve a pip on the outside. It's fitted with the thickest cork washer available (5/32") and the gasket is coated with Wellseal. I've only done the inner face for the moment as I will want to take it off again.


Test fit:

That's it for now. Next I will probably fit the dynamo drive sprocket and it's seal, but then to do any more in here I need the dynamo and the Automatic Timing Device. Both of these bits need rebuilding.

Tuesday, 18 June 2019

Brown Trouser Moment

I've had a few nervous moments in SQ4 ownership, shared by several co-owners if the stories on the AOMCC forum are anything to go by. Not least of these are the few occasions where oil pressure has suddenly and completely disappeared, accompanied by a more or less continuous return flow to the oil tank.

Fortunately, the first time this happened was on start up - or at least, that's when I noticed it. Investigation was interesting - removing the front main bearing cover to look at the oil pressure relief valve revealed that the spring had become caught in the split pin, and the split pin was now part way down the spring, preventing the spring exerting any pressure on the ball and allowing it to come off it's seat.

I put it back, noting that the direction the spring was wound in would always allow that to happen and wondered if original springs are wound in the opposite direction.

It happened twice more - once outside a smoke house along the coast. Knowing what it was, it was any easy fix if a little nerve racking - everything was rather hot, and I was nervous of losing small parts in the dirt. However, I was buoyed up by another motorcyclist stopping to see if I was OK.

The next morning, the same thing happened - very low, but not zero, oil pressure on start up. It had happened again.

I needed to do something. The spring lives in a bore which is a little over 6 mm - I can't measure it, but a 6 mm drill is a rattle fit while a 1/4" drill won't go in. The spring is about 5.5 mm OD and 4.5 mm ID:


I planned to make a brass cap to house the end of the spring, preventing the split pin from coming into contact with the coils.

However, I came across this cable ferrule which fitted beautifully. all I have done with it is to drill it out to 3.5 and use a needle file to open it a little more - all the relieved oil has to pass through this hole:


This works perfectly, and makes it much easier to get the split pin in.

Wednesday, 3 December 2014

Oil... everywhere

So a few days later and I run the engine with the front main bearing cap off. I'm not going to show you a picture, because there would be oil everywhere, but you can see from this shot with the cap loose that there is oil there; with it off it gushes out:


And here we have a new spring just arrived from Draganfly, about 25% longer and somewhat stiffer than the old one:


And here we have an oil pressure gauge showing a previously unreached figure, 55 psig, at tickover - engine relatively cold (about 5 minutes running). Thats more than 50% up on last time.


So now we need a road test. Yippee!



Saturday, 29 November 2014

Another Four Miles


Well, I have had the timing cover off and the pump is solid, so I have stripped the relief valve to reseat it. Oil pressure after a four mile run today is much the same, as we await the new spring.

Still, she's running a treat and she looks lovely!

So to get my head around engineering behind the oil pressure regulator I need to confirm what size the ball seat is, i.e. the diameter of the oilway in the offside end of the front crank. The ball is 3/16", so the seat must be maybe 5/32"? I'm trying to understand what the spring rate would need to be for a given back pressure in the system.

For example, a 5/32" seat would give an area of 0.019 sq in. exposed to pressure, so a 1 lb spring would give me about 50 psi. My existing spring is not that heavy (its the original one, new one on the way) and, surprise surprise, does not achieve 50 psi on the gauge - thats assuming the valve is ever opened!




I plan to have a look and see if the regulator valve is used next time I run the engine, and I will have to find a way of calibrating the pressure gauge..

Monday, 24 November 2014

Latest trip

Well, a bit more news today, and a four mile trip around town. 

The fuel filter has gone back in the spares box to be replaced by a plain pipe and a gauze strainer in the carburettor banjo - all air locks now banished to the spares box along with the fuel filter. Apart from a very fast tickover, all seems well in the fuel department.

I've been looking at more loose ends. I had meant to look at the chain oiler screw in the primary case for a while, since the thread in the primary chain case was refusing to allow the oiler screw to pass through it. I measured it, found it was 2 BA and cleaned it out only to realise that the screw I had was just an old carburetter mixture screw and was way too short. This is what it is supposed to look like:


Thanks to Steve Clarke for this picture.

The clutch has seen some adjustment and a much better cleanup job on the splines. It's dragging a little, but a vast improvement over what I had. Changes whilst riding are noiseless - engaging first at a standstill is still noisy but much less so. By the time I had got back it seemed to have loosened up and needed adjusting again.

The electrics are all behaving themselves; the handling is also fine but as I have discovered before I need to keep an eye on the tyre pressures - 28 in the front and 24 in the rear seems to be about right, and the consensus of opinion canvassed on the splendid AOMCC forum.

I've re-torqued the head, as regular blog readers will know. Cold, the oil pressure is about 35 psi - but this dropped to about 10 psi with the engine hot, so do we think the relief valve could be due for a new spring? AOMCC wisdom suggests that the Morgo pump may have loosened off (thanks Mark) so we will have to have a look at that before the next trip. I will get a new spring for the relief valve as well. It's getting properly hot now, but the engine is quiet and I have no exhaust or oil leaks.

Looking forward to the next trip!